PoliAdhesive®15-W, White Tile Adhesive

DESCRIPTION OF PRODUCT
PoliAdhesive®15-W is a cement based highly stable adhesive used in adhesion of tiles, ceramics,mozaic and marbles.

FIELDS OF APPLICATION
-In inner and outer areas for vertical and horizontal applications. 
-In the adhesion of tiles, ceramics, and marbles in bathrooms, kitchens, and corridors.

FEATURES AND BENEFITS
-Easy to prepare and apply 
-Long process time 
-No sliding in vertical applications. High adhesion property

APLICATION PROCEDURE
Preparation of Substrate
Application surface has to be strong, dry, bearing, dustless, clean, and also in balance. Surface must be cleaned off all kinds of oil, grease, rust, and paraffin traces that can weaken adherence and no loose particles must be present. Disordered surface with 5 to 20 mm depth must be repaired with PoliRepair 35 repair mortars two days before the application. If the application surface is over +25˚C, then it must be moisturized.
is applied by serrated side of trowel in single direction in uniform thickness. In the adhesion of ceramics or tiles with different thicknesses, to repair the disorder on application surface, it is suggested to apply 1 mm mortar under each ceramic or tile. When applying ceramics or tiles to the place of application, pavements are floated on mortar to enable full contact of adhesion mortar.

Suggested joint gap according to applied ceramic or tile dimension is left and the application is finished. To fill the left joint gaps, POLİKROM joint grouts must be used. Grouting of joints can be realized after approximately 24 hour

Mixing
Necessary amount of water is poured into a clean mixing container with the help of a scale. PoliAdhesive®15-W is slowly added to the water and mixed with a 400-600 RPM mixer for 3-5 minutes until a homogenous and unlumpy mixture is obtained. After resting it for approximately 3-5 minutes and mixing again for 30 seconds, the material is ready to use.

Mixing Ratio

APPLICATION METHO
1 mm PoliAdhesive®15-W is applied on application surface with the flat side of trowel. In an area that can be covered in 20 minutes, period of open waiting, PoliAdhesive®15-W is applied by serrated side of trowel in single direction in uniform thickness. In the adhesion of ceramics or tiles with different thicknesses, to repair the disorder on application surface, it is suggested to apply 1 mm mortar under each ceramic or tile. When applying ceramics or tiles to the place of application, pavements are floated on mortar to enable full contact of adhesion mortar. Suggested joint gap according to applied ceramic or tile dimension is left and the application is finished. To fill the left joint gaps, Polikrom joint grouts must be used. Grouting of joints can be realized after approximately 24 hours.
Applicability Test of Adhesive (Period of Open Waiting)
Fingers are pressed on the adhesive applied surface. If the adhesive smeared on the fingers, application of ceramics or tiles is continued. If the fingers are clean, it means the application time of adhesive has passed. In this case, the adhesive is scraped off the surface and new adhesive is applied.

Suggested Joint Width

Suggested Reed Dent Dimensions

WATCH POINTS 
-If environmental temperature is below +5˚C or over  +25˚C in PoliAdhesive®15-W application, then suitable temperatures must be waited for. Also PoliAdhesive®15-W application should not be made in very hot, rainy or windy weathers. 
- PoliAdhesive®15-W spread thickness must not exceed 6 mm (min. 3mm). Ceramics with high water absorption have to be watered well before application. 
-Under no circumstances, water and new material must be added to drying PoliAdhesive®15-W

COVERAGE

PACKAGING
25 kg polyethylene reinforced kraft bag

STORAGE
Must be stored in unopened original packing, and in cool and dry environment protected from freezing. In short-term storing, maximum 3 palettes can be stowed on top of each other and delivery has to be according to first in first out system. In long-term storing, the palettes must not be stowed on top of each other.